Whirlpool washer door wont open

When you wash a load of laundry, the door or lid to your Whirlpool washer locks as a safety feature. This prevents the machine from being opened mid-cycle, which would result in water leaking out or poses a hazard from the rapidly spinning basket, whirlpool washer door wont open. Newer models will no longer fill with water when the lid is raised, it must be lowered in place for the wash cycle to start.

Whirlpool will be using the following information we gathered from the external platform you selected to create your account. The door will not immediately unlock while the cycle runs due to a possible high water level in the washer, high water temperature, tumbling, or spinning. It may take up to five minutes for the washer to stop spinning and draining before the door will unlock. You will hear the door click when it unlocks. Verify that the drain hose is connected per the installation instructions. The drain hose should not be more than 4.

Whirlpool washer door wont open

This is for your own safety and to prevent water from leaking out of your appliance. Sometimes, the washer door might lock and stay locked. When this happens, something is most likely wrong with one or more internal components, which will need to be repaired or replaced. If you see no risk of water leaking out of your Whirlpool washer and the motor has completely stopped after the cycle, you can unlock the door by following these steps:. If the reset worked, you can use your washing machine normally as the problem was likely not with any components. Below, we discuss the main components to check and how you can fix them. The lid switch has a striker that needs to work correctly for the door to be able to be opened at the end of a cycle. The next possible cause of your Whirlpool washer door not unlocking is a faulty actuator motor. When the actuator motor becomes defective, your washer might turn off during a cycle, which can stop the door from unlocking. The next component to check is the drain pump. Your final option is to replace the main control board. You must be logged in to post a comment. How To Unlock a Whirlpool Washer.

This is typically a case of the door or lid NOT locking, instead of staying stuck locked. Once the new lid switch is installed, make sure the problem has been solved.

.

When you wash a load of laundry, the door or lid to your Whirlpool washer locks as a safety feature. This prevents the machine from being opened mid-cycle, which would result in water leaking out or poses a hazard from the rapidly spinning basket. Newer models will no longer fill with water when the lid is raised, it must be lowered in place for the wash cycle to start. The lid locking mechanism is an important safety feature, and not something that you should try to bypass. Washer baskets in top-load machines spin at extremely fast revolutions in order to remove the water from your laundry. Opening the washer lid while this spins and reaching inside could cause serious injuries. For this reason, modern Whirlpool top-load washers will lock the lid while the machine is running, and the lid will not unlock until the motor has completely stopped. It can take a few minutes for the washer to stop completely, this is normal! The display on your washer control board should have a light that indicates where the washer is in the cycle, and if the machine lid is locked or unlocked. Be sure to wait until the light is out before attempting to open the washer lid, you could damage the machine if you force it open.

Whirlpool washer door wont open

Whirlpool will be using the following information we gathered from the external platform you selected to create your account. The door will not immediately unlock while the cycle runs due to a possible high water level in the washer, high water temperature, tumbling, or spinning. It may take up to five minutes for the washer to stop spinning and draining before the door will unlock. You will hear the door click when it unlocks. Verify that the drain hose is connected per the installation instructions. The drain hose should not be more than 4. See installation instructions for further information.

Condo games roblox

The actuator presses down on the switch when the lid is closed, which lets the washer know it can start the wash cycle. If cleaning this out does not resolve the issue, you may need to further inspect for misalignment, or replace these parts. Check if the door can open. Replacing this part is as easy as unscrewing the damaged door strike and screwing a new one into place. Pin It. This is for your own safety and to prevent water from leaking out of your appliance. Schedule Service. I'm impressed. You must be logged in to post a comment. For more information about our privacy practices and a list of affiliated brands, please read out Privacy Notice. The lid locking mechanism is an important safety feature, and not something that you should try to bypass. This is a safety feature and prevents the water from flooding into your laundry room. If not, inspect the drain pump. When disconnecting and reconnecting wires to the control board, you may find it beneficial to take a photo for reference before beginning. If you have a front-load washer, the door latch may be causing your locking issues.

Washing machines are an indispensable part of our busy lifestyles. We rely on being able to throw in a load of laundry and go on with our day.

While the above parts are more likely to cause an unlocking issue with your washer, a control board that is failing may also prevent the door or lid from opening. You'll only be billed when your order ships. This will help ensure you match the proper wires to the correct terminals. The lid locking mechanism is an important safety feature, and not something that you should try to bypass. If the lid switch fails the test, replace it. News and Tips. After three seconds, you should be able to open the door. It can take a few minutes for the washer to stop completely, this is normal! Check if the door can open. Customer Financing. Be sure to wait until the light is out before attempting to open the washer lid, you could damage the machine if you force it open. Follow this process to inspect the drain pump: Make sure the power is switched off to your Whirlpool washer.