Ps vita joystick mod

Log in Register. Search titles only. Search Advanced search…. Home What's new Latest activity Authors.

Forums New posts Search forums. Groups Public Events. Reviews Overview Official reviews. Downloads Latest reviews Search resources. Blogs New entries New comments Blog list Search blogs. Chat Top chatters. Search Everywhere Threads This forum This thread.

Ps vita joystick mod

Are your eyes bleeding? You can always change your theme. Advanced search bounce or buckle? Welcome, Guest. Please login or register. Did you miss your activation email? News: Are your eyes bleeding? Quote from: Camineet on Tue, 26 January , Camineet Thread Starter Posts: Hey guys, not much of an update as far as progress goes. A while back as part of a failed design improvement, the device was unusable for almost 3 weeks and I had a bloodlust built up that was pretty out of control So, I haven't had a chance to get to work on implementing the additional analog sticks on top because I've been too busy satisfying my bloodlust for the past 2 weeks or so. I've also been chasing around a performance problem whereby one of the switches just dies for as long as 2 to 3 seconds at a time. I think I have located the problem which is a weak looking soldering point on the teensy, and I resoldered it, but I can't be sure that I resolved the problem until I have a few games to confirm.

BakerMan : today is a pretty damn nice day, and it's saturday. There was nothing I was ever able to do to get the single dead axis to revive.

.

This guide takes you through the process of installing the left joystick on the PlayStation Vita. Using a Phillips 00 screwdriver, remove the four 6. Using your fingernail or a spudger, pry open the accessory port cover on the top of the device. Using a Phillips 00 screwdriver, remove the two 5. Remove the two 5. Beginning at the sides of the device, use a plastic opening tool to separate the front and rear cases. There are still wires holding the front and rear cases together. You may damage the connections if you yank the cases completely apart. Gently separate the two cases, minding the battery and the touch screen controller connectors holding the two cases together.

Ps vita joystick mod

Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community. Already on GitHub?

Poppy drawing

It isn't reasonable for us to expect any kind of guaranteed performance when this friend is essentially doing a favor. I noticed that making the big solder connective blob took a long time and the tiny board got very hot in the process. I tried it just now, and it works well Recently I have just been playing every day and enjoying. Since you can touch the outside of the case with aluminum and a wire, I decided to see if I could instead touch the inside of the touch panel. New posts. From left to right Pin 1- 1. After a new wireup, if I move up-and-down on the good axis, it doesn't seem to exacerbate the bad axis getting stuck. I have read all of the threads explaining how and why doing so is not viable. Thanks for the feedback guys I think I may have resolved those problems with some soldering because I haven't seen either the problem with the intermittently dying switch or the intermittently moving analog in about two or three games after some extra soldering. I'm guessing that the materials don't present any problem and that the material in the ribbon cable will adhere to and make a connection with solder. When I first connect the device in the course of a new wireup, the analog is not stuck and functions properly for at least a few seconds.

Log In Sign Up.

The Nintendo 3DS is already past its prime, both in life-cycle and its homebrew scene, and while its homebrew scene still continues to be strong to this day, many You got the gist though. Or does it only get stuck after you've pressed it a certain way e. Second, and perhaps more importantly, the work required in order to position the third analog stick lower or deeper, depending on how you think about it such that it is in line with the placement of the primary stick would require unearthing of the mod for the primary stick. Then it converts rectangular to polar coordinates so you can adjust the central deadzone with just one parameter. I have never tried doing a new wire up, connecting the device, seeing that it is not stuck, and just letting it sit there to see if it becomes stuck. Just noticed a mistake in my code, it should say: Code: [Select]. I have chosen to accept this design flaw for a couple reasons. After separating the pinouts of the ribbon cable like fingers, I plan to try to take stranded wire and wrap one finger at a time once or twice around. Today at AM.