Replace pull cord on mower

The pull cord is used to start the lawn mower; it can often become broken or need replacement. Additionally, make sure you have a large table for the replacement and a rag nearby for wiping off any grease and oil.

This DIY lawn mower repair guide has instructions for how to replace a lawn mower starter rope. Over time, the starter rope can wear out and eventually break, and the mower won't start. You can replace a broken recoil starter rope with a manufacturer-approved replacement part by following the steps below. Remove the dipstick tube from the engine and plug the hole with a paper towel to keep debris from falling into the engine. Remove the bolts securing the blower housing to the engine and remove the housing from the engine.

Replace pull cord on mower

Eventually, you're lawnmower pull cord will break. Fortunately it's an easy fix. Check out this video on how to fix Few things are more frustrating than going to cut the grass or clear your driveway of snow and ending up with the starter cord in your hand. Eventually, it happens to everyone. When it does, check out this video on how to fix a lawnmower pull cord. First, remove the recoil from the engine. Most are held in place with three to five bolts. After removing the recoil, remove the broken cord. Next, measure the old pull cord. Add about four inches to the overall length to account for the knots you need to tie on either end. Add additional length as needed if the cord broke farther from the handle. Most of the time, however, the cord will break at the handle. In this case, you can simply reuse the existing cord.

Use your hands to lift the engine cover off, separating it from the rest of the engine. If you choose to remove the pulley, wear eye protection.

By: Author John Cunningham. Replacing a pull cord can be challenging, especially if the recoil spring gets loose. Taming a recoil spring can be like herding cats. Replacing the cord requires the removal of the pull start assembly. Some manufacturers, like Honda, make it easy. Other mowers may take a little more work.

At some point, all household maintenance tools are subject to wear and tear, and your lawn mower is no exception. A broken lawn mower pull cord is a pretty common problem. And fortunately, it is easy to get done DIY. When a pull cord is broken, it means that the starter rope has detached from the rest of the cord. The starter rope is the visible part of the cord. You can access it from outside of the mower. Make sure you replace it if it breaks. Usually mower pull cords break from regular wear and tear, but your cord may have broken because:. It just takes about 30 minutes. You can find the tools you need at home or at your local hardware store.

Replace pull cord on mower

Unless your mower is an electric model or less than three years old, breaking or fraying the pull cord on a mower is fairly common. However, repairing or learning how to replace a pull cord on a mower does require a bit of general knowledge. Knowing the name of each pull cord component should make it easier as you go through this guide and help you understand the role of each part. Step 1 — Watch This short video that shows you step-by-step instructions on replacing the pull cord on a lawnmower. Needle-nose pliers.

Thomas and friends toy

Untie the temporary knot you made earlier. Blockage — Grass and stuff stopping the blade from turning, the simple fix here. Cody Nitardy - Jul 21, Reply. The pull cord is used to start the lawn mower; it can often become broken or need replacement. Attach the other end of the rope to the starter handle. When it does, check out this video on how to fix a lawnmower pull cord. Now back the pulley off a full rotation, plus enough extra to align the tie-off hole in the pulley with the cord guide hole in the housing. Align the hole in the pulley with the hole in the housing and insert a screwdriver through the holes to keep them aligned as you work. Just set the housing back in place and reinstall the bolts. Small - px Medium - px Large - px. Anyone know how to fix a carb fire. Choose a symptom to see related walk-behind mower repairs.

Now you could let the pull cord snap just before you want to start mowing, but this makes for a long day. Pull cords on lawn mowers are usually made of a pretty strong nylon rope. While nylon rope is a sturdy material, the friction between the rope and the starter housing will eventually wear it down.

Turn it clockwise to unhook it from its tang. Main causes: dirty carburetor, bad spark plug, clogged air filter, engine choke problems, clogged gas cap vent…. Step 1 Pull Cord. Turn the rope pulley counter-clockwise 7 times to wind the spring. Thread your new starter cord through the housing and reel then tie a knot in the end. This cord is as cost-effective as it is reliable with a Dacron polyester solid-braid construction resistant against abrasion and wear. Main causes: damaged cutting blade, loose cutting blade, damaged flywheel key, engine needs tune up…. Do not proceed until you are confident that you understand all of the steps and are capable of completing the repair. Attach the rope to the starter handle. The spring loaded cord reel spring pulley is attached to the underside of the housing. Knot — Pull it through and knot it. Blower Assembly — Move to a workbench. Make sure the the engine is off and the spark plug wire is removed and away from the spark plug before begining. The pull cord is used to start the lawn mower; it can often become broken or need replacement. Remove the screws that secure the fuel tank to the engine.