Playstation 2 laser replacement

Disconnect all cables from the console and flip the unit over to reveal its base. Locate the 6 feet on the base of the unit. Pry them off using a spudger playstation 2 laser replacement reveal the screws. Note: One of the feet is located under the sticker shown in the photo.

Replace the laser assembly in your optical disc drive. Replacing the laser requires you to have or purchase a new laser. Flip the PlayStation 2 over so it lays with the bottom of the device facing upwards. Some models have a different number of screws and feet. Remove all the feet and screws in the bottom of the case. The 10 screw model has 6 screws in the bottom-most portion and 4 in the upper tray. Peel the warranty sticker located next to the main power switch straight away from the case.

Playstation 2 laser replacement

Use this guide to help identify which optical laser lens replacement will fit your PlayStation 2 console. Note: Replacing the laser lens will normally require a soldering iron to remove an anti static point solder blog before install. Laser lens models can normally be identified from the console model but it is always advisable to physically remove and check the old laser prior to ordering any replacement to ensure that it is the model you expected, and that the new part is the same model or listed as a compatible replacement for the model of laser you have. Lasers will need to be fitted to the deck unit inside the console, this requires some additional rebuilding, unscrewing runners to remove the old laser and put the new one in place. This is only a few additional steps but if you are less confident with completing the repair, or you believe other parts of the laser mechanism is not working properly, you can opt to purchase the deck with the laser pre-installed. Remember the anti static solder blob will still need to be removed prior to installation or the laser will not operate, this applies to all laser units, whether attached to the deck or not. This site uses cookies to provide you with a great user experience, by using ZedLabz. Discover the latest stuff from our wide range of partners, including exclusives only available at ZedLabz. Gaming display stands See More "Close Cart". Merchandise See More "Close Cart". Brands See More "Close Cart". Leave a comment Name Email.

Step 3. Open the ZIF connector. To facilitate the removal, it is recommended to pry open the half closer to the power switch first while rocking the top cover towards the front of the bottom case.

.

Disconnect all cables from the console and flip the unit over to reveal its base. Locate the 6 feet on the base of the unit. Pry them off using a spudger to reveal the screws. Note: One of the feet is located under the sticker shown in the photo. Removing this sticker will void any warranty with Sony. Remove all six 4.

Playstation 2 laser replacement

Use this guide to help identify which optical laser lens replacement will fit your PlayStation 2 console. Note: Replacing the laser lens will normally require a soldering iron to remove an anti static point solder blog before install. Laser lens models can normally be identified from the console model but it is always advisable to physically remove and check the old laser prior to ordering any replacement to ensure that it is the model you expected, and that the new part is the same model or listed as a compatible replacement for the model of laser you have. Lasers will need to be fitted to the deck unit inside the console, this requires some additional rebuilding, unscrewing runners to remove the old laser and put the new one in place. This is only a few additional steps but if you are less confident with completing the repair, or you believe other parts of the laser mechanism is not working properly, you can opt to purchase the deck with the laser pre-installed. Remember the anti static solder blob will still need to be removed prior to installation or the laser will not operate, this applies to all laser units, whether attached to the deck or not. This site uses cookies to provide you with a great user experience, by using ZedLabz.

Radio la otra ecuador

Pull the optical disc drive laser ribbon cable straight away and out of its socket. Almost done! Laser lens models can normally be identified from the console model but it is always advisable to physically remove and check the old laser prior to ordering any replacement to ensure that it is the model you expected, and that the new part is the same model or listed as a compatible replacement for the model of laser you have. Badges: Lasers will need to be fitted to the deck unit inside the console, this requires some additional rebuilding, unscrewing runners to remove the old laser and put the new one in place. What you need. Another way for calibrating is to remove said disc and if lens and ribbon move all the way forward and all the way back 3 or more times then you are almost done. Author with 7 other contributors. All new Lenses have this somewhere in the circuitry. Note: Replacing the laser lens will normally require a soldering iron to remove an anti static point solder blog before install. Step 10 Place the new laser in. Carlos Bragatto - Feb 16, Step 3.

The screws on the right are a bit deeper inside the shell as like the rest but are the same size.

It's important to remove the anti-static security, otherwise it won't work! View Statistics:. Add a comment. Remove the four 6. At that point plug in tv chord and place in a disc if the PlayStation 2 logo comes on and disappears in less than 3 seconds carefully replace all parts and your good to go. Use your fingernail to flip up the retaining flap on the optical disc drive laser ribbon cable. Be carefull, as it still attached to the laser, just guide it slowly towards yourself. Step 1 Top Cover. Note: You may use your hands for additional force to separate the two pieces of the outer shell. Step 8 Desoldering the anti-static security.