Lawn mower starter cord replacement

Now you could let the pull cord snap just before you want to start mowing, but this makes for a long day. Pull cords on lawn mowers are usually made of a pretty strong nylon rope.

This DIY lawn mower repair guide has instructions for how to replace a lawn mower starter rope. Over time, the starter rope can wear out and eventually break, and the mower won't start. You can replace a broken recoil starter rope with a manufacturer-approved replacement part by following the steps below. Remove the dipstick tube from the engine and plug the hole with a paper towel to keep debris from falling into the engine. Remove the bolts securing the blower housing to the engine and remove the housing from the engine. Turn the rope pulley counter-clockwise 7 times to wind the spring.

Lawn mower starter cord replacement

By: Author John Cunningham. Replacing a pull cord can be challenging, especially if the recoil spring gets loose. Taming a recoil spring can be like herding cats. Replacing the cord requires the removal of the pull start assembly. Some manufacturers, like Honda, make it easy. Other mowers may take a little more work. If your spring is damaged or unravels, go ahead and buy a whole spring and pulley. This post covers pull cord replacement pretty well. Your mower may look different from the models used in the demo shots here, but no matter the repair procedure will be very similar to most mowers. Pull the cord out all the way, secure the pulley, use a screwdriver to lock the spokes of the pulley, and stop it from retracting. Fit the pull handle and double knot.

Now you could let the pull cord snap just before you want to start mowing, but this makes for a long day. Read more.

With perfect weather, you plan to go out to give your lawn a nice trim. You use a push mower that has never let you down in all these years. The other end is spinning back into the starter assembly. You are not the only one with this problem. It occurs more frequently with older lawnmowers, and in most cases, you have to replace the pull cord.

Written by: Steve. October 3, As an Amazon Associate we earn from qualifying purchases more. If you own a pull start lawn mower you will eventually find yourself holding the severed handle of a broken starter cord. Here in Florida, two thirds of the year is one continuous lawn mowing session. That translates to lots of cord tugs. Thankfully, starter cord replacement is simple wear and tear maintenance that you can easily do yourself.

Lawn mower starter cord replacement

Are you struggling with a broken pull cord on your lawnmower? With our step-by-step instructions, your Briggs and Stratton lawnmower will be up and running quickly. How to replace the pull cord on a Briggs and Stratton lawnmower:. Remove the cover, tank, and shroud. Cut the old cord, rewind the spring, and lock the pulley.

Fenerbahçe zenit canlı maç yayını

Added to your cart:. To do this, first put a mark on this rope according to the length required and then cut the end using a pair of scissors. October 2, at pm. August 15, at pm. Remove the screw that secures the dipstick tube to the housing. Remove the paper towel from the dipstick opening, slide the dipstick tube into the engine and secure it with the screw. June 29, Rubbing a small amount of oil on the end of the pull cord helps it slip through. Bobby Mcdonalid says:. We know that after this hectic job, you might be a little tired. Now that you know how to replace a mower pull cord, you can move onto your next DIY repair or improvement project. June 7, at am. It would be best if you had the following equipment at your disposal to help you with the process:.

At some point, all household maintenance tools are subject to wear and tear, and your lawn mower is no exception.

If there is too much excess, cut it off using scissors. Snag this cord in either 4, 5, or 6 diameters and lengths of 10ft and 25ft, or spools of 50ft, ft, and 1,ft for a never-ending supply of replacement pull cord perfect for everything from mowers, generators, leaf and snow blowers, and more. Glad you found the article helpful! Remove the plastic cap: 1. Avery Harvey says:. This cord is as cost-effective as it is reliable with a Dacron polyester solid-braid construction resistant against abrasion and wear. Choose a symptom to see related walk-behind mower repairs. Benjamin Reyes says:. Contents show. Replacing the cord requires the removal of the pull start assembly. The final step is to remove the whole engine shroud.