Ipod nano battery replacement

Replacing the battery requires a fine tip soldering iron and is a difficult job that only experienced solderers should attempt.

Front Page. How Tos. Buyer's Guide. Log in Register. Search Everywhere Threads This forum This thread. Search titles only. Search Advanced search….

Ipod nano battery replacement

The iPod Nano 6th Generation battery is not a plug-and-play battery. This process requires delicate desoldering to remove the old battery. Use a heat gun or hair dryer to soften the adhesive securing the perimeter of the front panel assembly to the outer case. Be careful not to overheat the front panel assembly, as it may result in damage to the LCD. While the front panel is still warm, use the edge of an opening tool to pry it from the headphone jack side of the front panel assembly out of the Nano. Do not attempt to pry out the front panel assembly from, or insert the opening tool into the left side of the display, as the display data cable is right underneath and may be damaged in the process. Continue prying the perimeter of the front panel assembly out of the outer casing, being careful not to damage the display data cable held under its left edge. If the front panel is excessively difficult to lift out of the outer case, reheat the area and try again. Pull the front panel assembly slightly away from the left side of the Nano to clear the display data cable. Use an opening tool to pry the steel shield out of the Nano by its upper right corner. Use an opening tool to disconnect the display data and digitizer cable connectors up from their sockets on the logic board. To reassemble, you can use the double-sided tape found here. Use an opening tool to gently pry the battery up from the adhesive securing it to the outer case. The adhesive is very strong.

To reassemble your device, follow these instructions in reverse order, while being careful not to damage the iPod. I tried what Bradley suggested because it really seems easier than to solder the new battery to the iPod circuit board, which is really tiny. Ipod nano battery replacement heat buildup has the potential to ruin the logic board or melt the ribbon cable.

However, a variety of more affordable third-party services also are available. Third-parties offer battery replacement services for considerably less than Apple charges and often sell "longer runtime than stock" batteries for self-installation as well. If you are not sure which iPod nano you have, one way to externally identify these models is via a unique model number on the back of the device. These models also can be differentiated by serial number with Everyi. Like the model number, the serial number is toward the bottom on the back of the device or under the "teeth" on the clip and also is available when plugged into a computer on the "Summary" tab in a modern version of iTunes among other methods.

Replacing the battery requires a fine tip soldering iron and is a difficult job that only experienced solderers should attempt. Insert the edge of an iPod opening tool into the gap between the outer case and the top bezel. At this point the hold switch slider is free and may fall. Be careful not to lose it. Remove the two angled Phillips screws from the two corners of the display retainer. Do not rotate the display retainer about the top edge of the display, as it is attached to a thin steel bracket that is easily broken. Do not forcefully remove the display retainer, as the hold switch cable is liable to snap. Slide the display out of the Nano. It will move about. Use your thumbs on the lower edge of the glass panel to slide the glass down and into the case until the top edge pops up out of the case.

Ipod nano battery replacement

Make an appointment at an Apple Authorized Service Provider. We can replace your iPod battery for a service fee. We replace cracked screens for a fee. Accidental damage isn't covered by the Apple warranty. Apple Authorized Service Providers can set their own fees, so ask them for an estimate.

Csp colorize

Yes No. Original iPod nano A Sign Up. We'll inspect your product when we receive it. In our case, we started on the left. Nevertheless, for tech savvy individuals, there are videos available that cover battery replacement for the iPod nano line. This is in addition to your rights provided by consumer law. A shipping fee will be added if we need to ship your iPod. Be careful not to lose it. Select one Service type.

Arrange to mail your product directly to Apple.

Got a new battery. This is probably a stupid question but is there a way to put on the battery without solder? Step 21 Battery. But I'm worried about the swollen batteries on the other two ; How dangerous is it to operate on them when in such condition? Tritto said:. Top Bottom. I recently tried replacing the battery in a Nano 4. Separate the bottom bezel from the adhesive securing it to the Nano and set it aside. Please enable Javascript in your browser and reload the page. Badges: