How to unlock whirlpool washer control lock

When you wash a load of laundry, the door or lid to your Whirlpool washer locks as a safety feature. This prevents the machine from being opened mid-cycle, which would result in water leaking out or poses a hazard from the curecode spinning basket. Newer models will no longer fill with water when the lid is raised, it must be lowered in place for the wash cycle to start. The lid locking mechanism is an important safety feature, and not something that you should try to bypass, how to unlock whirlpool washer control lock.

Whirlpool will be using the following information we gathered from the external platform you selected to create your account. If the control lock has been activated, the control will not function. If you try to push buttons, you may see the code "LoC" or "LC" depending on your model. This is a reminder that you have set the control lock and need to de-activate it to allow the washer controls to function. Some models will look like the following:. This error code does not mean "Door Locked".

How to unlock whirlpool washer control lock

This is for your own safety and to prevent water from leaking out of your appliance. Sometimes, the washer door might lock and stay locked. When this happens, something is most likely wrong with one or more internal components, which will need to be repaired or replaced. If you see no risk of water leaking out of your Whirlpool washer and the motor has completely stopped after the cycle, you can unlock the door by following these steps:. If the reset worked, you can use your washing machine normally as the problem was likely not with any components. Below, we discuss the main components to check and how you can fix them. The lid switch has a striker that needs to work correctly for the door to be able to be opened at the end of a cycle. The next possible cause of your Whirlpool washer door not unlocking is a faulty actuator motor. When the actuator motor becomes defective, your washer might turn off during a cycle, which can stop the door from unlocking. The next component to check is the drain pump. Your final option is to replace the main control board. You must be logged in to post a comment. How To Unlock a Whirlpool Washer. Fred's Appliance. December 5,

This can be achieved by unplugging your appliance for 45 minutes. Activating the Control Lock: Touch and hold for 3 seconds to lock the controls to avoid unwanted changes or operation.

Whirlpool will be using the following information we gathered from the external platform you selected to create your account. When the control is locked, the cycles cannot be started or changed. It must be unlocked to operate or run a cycle. The Control Lock can also be set while the machine is running to prevent someone from stopping or changing a cycle. Please contact us or click below to make an appointment from our preferred list of service providers for service on your appliances. Hang in there, we are looking for alternate products just for you. We use your information in accordance with our privacy policy.

Last Updated: March 1, Fact Checked. With over 15 years of experience, Homer specializes in home improvement, remodeling, and construction. There are 16 references cited in this article, which can be found at the bottom of the page. This article has been fact-checked, ensuring the accuracy of any cited facts and confirming the authority of its sources. This article has been viewed , times.

How to unlock whirlpool washer control lock

This feature is designed to prevent children or anyone else from accidentally changing the settings on your washer. However, if you need to make changes to your washer, you will need to deactivate the Control Lock. Fortunately, the process is simple and only takes a few steps. You can now make changes to your washer settings. To deactivate the Control Lock on a Whirlpool washer, press and hold the Control Lock button for 3 seconds. The Control Lock light will turn off, indicating that the Control Lock has been deactivated. The control lock icon should disappear from the display.

Tattoo pergamino con nombres

December 5, Is this a good question? Pushing or pulling this tab should release the door latch, allowing the washer door to open. Once the new actuator motor is installed, make sure the problem has been solved. Fred's Appliance. When reaching in near the door latch assembly, you should feel a circular tab. The display on your washer control board should have a light that indicates where the washer is in the cycle, and if the machine lid is locked or unlocked. Continue Shopping. Was this answer helpful? To replace a lid actuator, remove the damaged one by lifting the lid of your washer and releasing the locking tab or screw holding the actuator in place.

Whirlpool will be using the following information we gathered from the external platform you selected to create your account.

The door strike works with the latch to keep your front-load washer door closed and locked. News and Tips. Troubleshooting at your fingertips Not sure where to start on that repair? This can be done by using a flathead screwdriver to unclip the panel, allowing it to be pulled off. Depending on your model, you may need to disconnect the back console before the lid will lift up. Mathilda Jobson was right. Text The location and method for removing and installing a new drain pump does vary depending on if you have a top-load or front-load, so searching our YouTube channel with your model number will help ensure you find the best instructions for your washer. To replace a lid actuator, remove the damaged one by lifting the lid of your washer and releasing the locking tab or screw holding the actuator in place. For a top-load washer, you can use a putty knife to release the locking tabs for the top panel. If the door does not unlock, continue reading below for troubleshooting or repair tips. Follow this process to inspect the lid switch: Switch the power off to your Whirlpool washer. The display on your washer control board should have a light that indicates where the washer is in the cycle, and if the machine lid is locked or unlocked. The end of cycle signal button is found on the right side of the panel the offers 3 options with red lights: Louder, Softer,and Off. If the lid switch fails the test, replace it.