Astm b221 pdf

Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes1 This standard is issued under the fixed designation B; the number immediately following the designation indicates the year of original adoption or, astm b221 pdf, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. This standard has been approved for use by agencies of the U. Department of Defense.

Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes1 This standard is issued under the fixed designation B; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. This standard has been approved for use by agencies of the U. Department of Defense. This specification may not address the Structural Pipe and Tube manufacturing processes, integrity testing, and verification required for B Test Methods for Tension Testing Wrought and Cast fluid-carrying applications involving pressure. See Specification B, as Wrought Products appropriate, for use in surface condensers, evaporators, and heat exchang- ers.

Astm b221 pdf

JavaScript seems to be disabled in your browser. For the best experience on our site, be sure to turn on Javascript in your browser. Not registered? Create an Account. This specification covers extruded bars, rods, wires, profiles, and tubes made from aluminum and aluminum alloys. All the products should be produced by hot extrusion or similar methods. The chemical composition of each material is determined in accordance with the specified suitable chemical and spectrochemical test methods. Samples for chemical analysis should be taken when the ingots are poured or from the finished or semi-finished products by drilling, sawing, milling, turning, or clipping. Tensile properties, elongation, and yield strengths of each product should conform to the requirements listed herein. Elongation requirements are not applicable for materials with sizes smaller than the specified limits. Note 1—Throughout this specification, the use of the term alloy in the general sense includes aluminum as well as aluminum alloy. Note 3—Structural pipe and tube produced in accordance with B is not intended for fluid-carrying applications involving pressure.

Certification him that the material meets the requirements of this specifica- Bar, Profiles, and Tube. M Tentative; properties subject to revision.

JavaScript seems to be disabled in your browser. For the best experience on our site, be sure to turn on Javascript in your browser. Not registered? Create an Account. This specification covers extruded bars, rods, wires, profiles, and tubes made from aluminum and aluminum alloys.

JavaScript seems to be disabled in your browser. For the best experience on our site, be sure to turn on Javascript in your browser. Not registered? Create an Account. The products shall be produced either by hot extruding and cold finishing or by hot rolling with or without cold finishing. Bars, rods, and wires shall conform to the chemical composition requirements prescribed for aluminum, silicon, iron, copper, manganese, magnesium, chromium, zinc, bismuth, lead, and titanium, and to the specified tensile properties such as tensile strength, yield strength, and elongation. Requirements for quality assurance, heat treatment, chemical analysis, tension test, heat-treat response, bend testing, and stress-corrosion resistance and stress-corrosion cracking test are detailed.

Astm b221 pdf

Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes1 This standard is issued under the fixed designation B; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. This standard has been approved for use by agencies of the U.

Current choghadiya

B Astm Document 1 page. Aluminum D. The producer shall maintain material. Table 2 and without the imposition of cold work shall be B - Aluminum Profiles Document 15 pages. Aerospace Material Specification Document 6 pages. Shipping and Handling charges are approximate. For the statistical analysis of at least 30 tests from at least 3 cast lots of products described, mechanical property limits are based on standard production material with no more than 10 observa- the statistical analyses of at least tests from at least 5 cast tions from a given heat treat or inspection lot. The individual Document downloaded may not otherwise be sold or resold, rented, leased, lent or sub-licensed. Alloy Extruded Wire, Rod, T5 up through 0. User Settings. Inert Pair Effect Document 7 pages. Reprints and Permissions Reprints and copyright permissions can be requested through the Copyright Clearance Center.

JavaScript seems to be disabled in your browser.

The electrical conductivity shall be determined in accordance with Practice E in the following locations: B When material is found to be unacceptable, it shall be reprocessed additional precipitation heat treatment or re-solution heat treatment, stress relieving, straightening, and precipitation heat treatment, when applicable. Tensile Properties of Material from Producer follows: 6. T Tempers Extruded Wire, Rod, T65 up through 0. O Extruded Tube up through 2. Chemical milling may be used on flat surface samples. Any requirement not so covered and purchaser. X0 or 0. Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes1 This standard is issued under the fixed designation B; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. No cure period will be provided for material breaches relating to violations of Section 3 or any other breach likely to cause ASTM irreparable harm.